Butt Weld Fittings are regularly supplied to global customers either as stand-alone orders or as part of our packaged solutions.
Stub ends are used to connect pipes together along with a lap joint or backing flange. A stub end is welded to the end of each pipe that requires connecting with a lap join flange slip over the top of it before welding. Because the stub end has a serrated face it acts to seal both the pipes together. The lap joint flange is then bolted together with the mating lap joint flange to secure it all in place. This in turn means that the pipes can be opened easily to inspect or clean them, as they are not welded together, merely bolted together.
Concentric reducers are used to reduce the flow or the size of a pipeline. Either end of the concentric reducer is of a different size and is manufactured to suit nominal bore pipe and its relevant scheduled wall thicknesses. The component has the same centre line throughout its length.
Eccentric reducers are similar to concentric reducers in that they reduce the flow or the size but there are a few differences. One side of the component is flat, which means that there is an off centre flow through the pipeline. The component is manufactured to suit nominal bore pipe and its relevant scheduled wall thickness.
Elbows are made in a variety of angles and radii. The standard angles are either 45 degrees or 90 degrees. The 45 degree elbows are only available as a long radius elbow, but the 90 degree is also available as both long radius and short radius elbows. The sole purpose of the elbows is to change the angle of the piping in the pipeline or application. Elbows are welded into place at each end.
Tees can be provided with either equal dimensions or a reduced outlet. The end result is much the same in that they are designed for the merging or diving of fluids within the pipelines. If a reduced outlet is used, this changes the flow and the size of pipes used within the pipeline system. Unlike a valve, which can leave any one of the outlets closed if required, the outlets on a tee cannot be closed off, unless they are physically blanked off with an end cap or something similar
|Minimum Order Quantity||10 Piece|
|Bend Angle||45 degree, 90 degree|
|Size||1 inch, 3/4 inch, 2 inch, 1/2 inch, 3 inch|
|Application||Gas Pipe, Chemical Handling Pipe, Plumbing Pipe, Drinking Water Pipe, Structure Pipe|
|Minimum Order Quantity||10 Piece|
|Size||1 inch, 2 inch, 3 inch, 1/4 inch, 3/4 inch|
|Connection||Female, Male, Welded, Flange|
|Elbow Bend Angle||180 Degree, 30 Degree, 45 Degree, 60 Degree, 90 Degree|
|Application||Chemical Fertilizer Pipe, Hydraulic Pipe, Structure Pipe, Gas Pipe, ALL|
|Size||>20 inch, 1 inch-2 inch, 10 inch-20 inch, 3 inch-10 inch, 2 inch-3 inch, 1/4 inch-1 inch|
|Material||Brass, Copper, MS, SS|
|Connection||Female, Welded, Male, Flange|
|Application||Hydraulic Pipe, Structure Pipe, Gas Pipe, Chemical Fertilizer Pipe|
|Size||2 inch, 3/4 inch, 1/2 inch, 1 inch, 3 inch|
|Application||Gas Pipe, Hydraulic Pipe, Pneumatic Connections, Chemical Fertilizer Pipe, Structure Pipe|
|Minimum Order Quantity||5 Piece|
|Application||Pneumatic Connections, Gas Pipe, Structure Pipe, Hydraulic Pipe, Chemical Fertilizer Pipe|
|Size||1 inch, 3/4 inch, 1/2 inch, 3 inch, 2 inch|
We are the leading manufacturer of various types of butt weld fittings that ranges from Elbow, Tee, Reducer, Cap, Stu bend, Bends, Nipple etc. We manufacture these products in varied specifications with regard to size, type and form. Our range of Stainless Steel 321 Buttweld Fittings are fabricated with high quality stainless steel and widely appreciated for their corrosion resistance and high durability properties.